mirror of
https://gitea.com/mcereda/oam.git
synced 2026-02-09 05:44:23 +00:00
131 lines
4.0 KiB
Markdown
131 lines
4.0 KiB
Markdown
# OpenSUSE
|
|
|
|
## Table of contents <!-- omit in toc -->
|
|
|
|
1. [Enable Bluetooth pairing on boot](#enable-bluetooth-pairing-on-boot)
|
|
1. [Enable SSH access from outside after installation](#enable-ssh-access-from-outside-after-installation)
|
|
1. [Raspberry Pi](#raspberry-pi)
|
|
1. [Firmware update from a running system](#firmware-update-from-a-running-system)
|
|
1. [Rollback from a bootable snapshot](#rollback-from-a-bootable-snapshot)
|
|
1. [Further readings](#further-readings)
|
|
1. [Sources](#sources)
|
|
|
|
## Enable Bluetooth pairing on boot
|
|
|
|
1. enable the `bluetooth` service on boot
|
|
1. install `bluez-auto-enable-devices`; this will create the configuration file `/etc/bluetooth/main.conf`
|
|
|
|
Also see specific settings in the [Bluetooth] KB.
|
|
|
|
## Enable SSH access from outside after installation
|
|
|
|
Open port 22 on the firewall:
|
|
|
|
- using Yast:
|
|
|
|
1. open _Yast2_ > _Firewall_
|
|
1. make sure your interfaces are appointed to the _External_ zone
|
|
1. check _ssh_ is in the _Allowed services_ column and add it to the list if not
|
|
1. save the configuration and exit (make sure the firewall is reloaded on exit)
|
|
|
|
- using [firewall-cmd][firewalld] on the command line:
|
|
|
|
```sh
|
|
sudo firewall-cmd --add-port=22/tcp --permanent
|
|
```
|
|
|
|
Start the SSH daemon:
|
|
|
|
- using Yast: open _Yast2_ > _System services_ and enable _SSHD_
|
|
- using [systemctl][systemd] on the command line:
|
|
|
|
```sh
|
|
sudo systemctl enable --now sshd.service
|
|
```
|
|
|
|
## Raspberry Pi
|
|
|
|
Install the OS from another computer capable of reading and writing SD cards.
|
|
|
|
Given `/dev/sdb` being a SD card, use the following:
|
|
|
|
```sh
|
|
curl -C - -L -o opensuse.raw.xz http://download.opensuse.org/ports/aarch64/tumbleweed/appliances/openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.aarch64.raw.xz
|
|
xzcat opensuse.raw.xz \
|
|
| sudo dd bs=4M of=/dev/sdb iflag=fullblock oflag=direct status=progress \
|
|
&& sync
|
|
```
|
|
|
|
Insert the SD card in the Raspberry Pi and power it on. The network is configured to get an IP address on `eth0` using DHCP.
|
|
|
|
Connect using SSH and login using `root:linux`.
|
|
|
|
### Firmware update from a running system
|
|
|
|
```sh
|
|
# Check for an updated firmware.
|
|
sudo rpi-eeprom-update
|
|
|
|
# Install the new version and reboot.
|
|
sudo rpi-eeprom-update -a && sync && reboot
|
|
```
|
|
|
|
## Rollback from a bootable snapshot
|
|
|
|
Do as follows:
|
|
|
|
1. boot the system
|
|
1. in GRUB's boot menu, choose _Bootable snapshots_
|
|
1. select the snapshot you want to boot into; the list of snapshots is listed by date, the most recent snapshot being listed first
|
|
1. log in to the system
|
|
1. carefully check whether everything works as expected
|
|
|
|
> You cannot write to any directory that is part of the snapshot. Data you write to other directories will not get lost, regardless of what you do next.
|
|
|
|
Depending on whether you want to perform the rollback or not, choose your next step:
|
|
|
|
- if the system is in a state where you do **not** want to do a rollback, reboot and boot again into a different snapshot, or start the rescue system.
|
|
- to perform the rollback, run
|
|
|
|
```sh
|
|
sudo snapper rollback
|
|
```
|
|
|
|
and reboot
|
|
|
|
On the boot screen, choose the **default** boot entry to reboot into the reinstated system.
|
|
|
|
A snapshot of the file system status before the rollback is created, and the default subvolume for root will be replaced with a fresh read-write snapshot.
|
|
|
|
## Further readings
|
|
|
|
- [Bluetooth]
|
|
- [Firewalld]
|
|
- [Systemd]
|
|
- [System Recovery and Snapshot Management with Snapper]
|
|
|
|
## Sources
|
|
|
|
All the references in the [further readings] section, plus the following:
|
|
|
|
- [OpenSSH basics]
|
|
- [Bluetooth on boot]
|
|
- [Raspberry Pi4]
|
|
|
|
<!--
|
|
References
|
|
-->
|
|
|
|
<!-- Upstream -->
|
|
[openssh basics]: https://en.opensuse.org/SDB:OpenSSH_basics
|
|
[raspberry pi4]: https://en.opensuse.org/openSUSE:Raspberry_Pi
|
|
[system recovery and snapshot management with snapper]: https://documentation.suse.com/sles/12-SP4/html/SLES-all/cha-snapper.html
|
|
|
|
<!-- Knowledge base -->
|
|
[bluetooth]: bluetooth.md#bluetooth-devices-cannot-be-used-at-login
|
|
[firewalld]: firewalld.md
|
|
[systemd]: systemd.md
|
|
|
|
<!-- Others -->
|
|
[bluetooth on boot]: https://www.reddit.com/r/openSUSE/comments/eoozm2/comment/feetqpn/
|